Allure Flooring Installation – Guide to Avoid Mistakes

Installing allure flooring is a very simple home project as it does not require adhesives, nails and other complicated materials. The truth is this type of flooring is installed without the need to actually attach it to the subfloor. So, how do you go about the installation process and how can you avoid the common problems and mistakes when it comes to installation?

Seven Step Guide to Allure Flooring Installation

Installing this type of flooring may be complex if you are not used to it, but these steps will show you how easy it is to lay it on your floor.

  • Measure – The first step is to measure the area where you will lay the flooring. Multiply the length by the width and make an allowance of 10% to compensate for damaged and lost materials. Make sure to sit the flooring for about 48 hours to acclimate it to the area.
  • Clean – Clean the subfloor and floor thoroughly prior to installation. Ensure that all debris and dirt are not present.
  • Lay – Start laying the vinyl flooring along the most visible area in the room. You must leave at least 1/8” gap for expansion. Connect each plank with the Grip Strips
  • Hold – Hold the next row of this type of flooring at an angle of 45 degrees, align the strips and press them all together.
  • Cut – Cut the vinyl material with the aid of ruler and a sharp knife
  • Stagger – It is important to stagger all the joints to make your flooring attractive and stable
  • Finish – Continue with the installation up to the final row and add trim as well as floor molding.

Installation Tips and Tricks

By following this guide, you can enjoy your flooring in no time so make sure you adhere with the instructions to avoid the mess.

No to Problems and Errors

Basically, all the errors that you may commit when installing this kind of flooring are avoidable. All you need to do is to spend more time reading the manual and you can get hold of all the necessary information for proper installation.

So that you can have an idea of the possible mistakes that you may have, take a look at the following:

  • Not letting the flooring to acclimate before the installation
  • Exposing the plank glue to dirt and dust
  • Not performing the right subfloor preparation
  • Not utilizing mold-inhibitor to areas that are prone to moisture
  • Not rolling the surface right after installation
  • Not having spare materials to cover up for the errors
  • Not guarding the floor from certain damages

Most of these issues are the result of not paying attention to the allure flooring manual. Just like with the odor which is common to all vinyl products. The odor can be resolved by allowing it to our out for one to two weeks. By knowing all these things, the entire installation process can be a pleasant and enjoyable experience for you.

Allure Flooring Tips

Allure Flooring Tips


Allure Flooring Installation – Steps and Tips

Trafficmaster is best known for allure flooring. It is a kind of vinyl flooring that can mimic the appearance of real hardwood, marble and other flooring materials. It is available in a variety of finishes and can be purchased at home improvement shops such as Home Depot. A lot of household make use of this material because it is a great alternative to the genuine flooring materials. But what do you have to know about its installation?

Flooring Tips

Making the Preparations

There are a lot of things that you need to consider prior to buying and installing this type of flooring such as the following:

  • Area – Prior to installing allure flooring, it is highly important that you know the measurements of the space where you wish to put in the flooring. This will help you identify how much of this flooring you will have to buy. Once you have determined the size, it is advised to add 10% to the total measurement to make room for discoloured planks or anything that may be lost or damaged during the installation process.
  • 48 hour waiting time – You cannot just install this flooring once you got it from the store. You need to wait for at least 48 hours before installing them to acclimate it to the humidity and temperature of your home.
  • Material – You need to know that allure flooring can be installed over different materials such as linoleum, wood, tile, concrete and even vinyl.
  • Floor compound – Prior to installation to a textured surface or tiled area, make sure that you spread adequate amounts of levelling compound.
  • Ridges and bumps – With the use of hammer, remove any ridges and bumps so it will not be visible through the floor surface.

The Installation Process

Once you have prepared all the necessary things, you can now begin installing allure flooring. Essentially, you need to begin with the most visible or longest wall within the space. After which, you can proceed with the following steps:

  • Cut the top connector of the first plank with the aid of a utility knife and put the smooth edge and make it face against  the wall
  • Make room for expansion by leaving 1/8” gap between the flooring and the wall
  • Put the next row to about 45 degrees angle and glide it to place with the use of GripStrip connectors.
  • Proceed with the installation across the floor and totter the joints of every row by about half a foot.
  • Run the floor roller all throughout the surface in order to eliminate the air or bubbles from the surface of the allure flooring.
  • Add the molding or trim across the surface to plaster the expansion gap that can be found on the bottom part of the wall.

By following all these steps and tips, installing allure flooring will be a huge success.

Trafficmaster Flooring


Allure Flooring Review – All the Facts You Need To Know

If you wish to make your home a lot cosier than it is right now, then you may want to invest in allure flooring.  It is a cost effective option if you want to beautify your home and the great thing is it is waterproof and very sturdy too. You can choose from adhesive and locking multilayer vinyl laminate and you are good to go.

What Are The Pros and Cons?

Using allure flooring can be an attractive option so if you are interested, you have to know its advantages and disadvantages. Basically, this type of flooring is the choice of many households because of the following:

  • It is affordable and not difficult to install
  • Can be installed over almost all types of subfloors
  • It is waterproof so it can be installed in the bathroom
  • Can resemble stone and wood perfectly
  • Wide array of styles and patterns to select from

On the other hand, this kind of flooring has some disadvantages too like as follows:

  • It is synthetic and can only be installed indoors
  • May have an annoying odor initially

How Much Do You Have To Pay?

allure Flooring Reviews

Allure Flooring Review

Now that you have an idea about this flooring material, you may be wondering by now how much it costs? Well, you can have a lot of options when it comes to allure flooring and these can be the best imitations of tile, hardwood and other genuine flooring materials. The best thing is that they are really affordable.

For instance, Allure Cherry can cost you about $2-3 per square feet which is the same thing with allure oak. Moreover, the allure flooring material that resembles marble is priced at $2.09 per square feet just like the neutral allure and allure ashlar. If you will compare it to other flooring materials, allure is a lot cheaper. Wood material is about four times more expensive than allure while other material such as Pergo is thrice its price.

Hence, the price of allure is good enough for it is a top quality and highly functional flooring. Plus, it looks like the genuine flooring materials out on the market so those who are on a tight budget can have more options.

How About the Maintenance?

Undoubtedly, this type of flooring can be an ideal choice for every home. It is reasonably priced, versatile, durable and nice looking. But then you may ask how about the cleaning? The good news is cleaning allure flooring is very easy. In general, all you need is a scotch brite and allure one step cleaner.

The scotch brite will remove all the scuffs or marks that are on the floor while the one step cleaner will aid in replenishing your floor most especially as it lasts overtime. You just have to remember that using wax on this vinyl flooring can damage it. So, make sure you take care of your flooring well enough to avoid the inconveniences and to make your allure flooring lasts longer.